Gravity Filter Compatible Settling Bucket Construction Kit

Do you have a settling bucket? A settling bucket is a holding container that allows sediment to naturally fall out of solution over time in order to reduce the amount of sediment your filter needs to remove from the water. Not only can it drastically prolong the life of your filter but also require far fewer disinfection resources. Make construction of your settling bucket simple and straightforward with our new settling bucket decal and kit. Please note that to reduce the cost of the three and five packs, they will NOT include multiple paddle bits. If you’d like multiple paddle bits, please purchase additional paddle bits OR multiple individual kits instead of the three or five packs.

Specifications - Specific treatment data and instructions in the pictures across the website has been omitted. All WDC products will arrive with these spaces filled with the actual data.

INCLUDES:

• 7/8” Wide, 1/4” drive, 6” long tool steel paddle (spade) bit

• 7/8” Tubing Compatible Spigot - 3/8” male barb - with on/off valve

• Instructions and alignment decal

• 7.5” x 9” - Please note this decal has specific alignment instructions for where and how to place it on a standard 5 US GAL bucket.

• The included spade (paddle) bit, when correctly used will neatly slice the decal out of the way for the placement of the spigot.

• Please be sure to install a seal on both the INNER and OUTER surfaces and finger tighten the nut until there is no leaking. DO NOT OVER TIGHTEN.

• High-Quality, matte finish

• Die cut

• UV resistant

• Waterproof

• Scratch Resistant

• Heat resistant

• High-tac adhesive

• Legible under NVGs

• Designed, printed, and packaged here in the USA

• For 3x Packs - Please note that this will only come with ONE paddle bit. Please add additional singles to your cart if required.

Sawyer Basic Kit Includes the following in addition to what is listed above:

• 1x Sawyer Mini Filter

• 1x Sawyer Backflush syringe with Cana Provisions Backflush Syringe Decal

• 1x 24” total section of US Made Silicone tubing

• 1x hose clamp

• 3x total Cana Provisions tubing labels (1x clean, 1x dirty, 1x untreated)

MSR ThruLink Kit Includes the following in addition to what is listed above:

• 1x MSR ThruLink Filter (Microfilter AND ACTIVATED CARBON ELEMENT)

• 1x set of male/female QD fittings

• 1x 24” total section of US Made Silicone tubing

• 1x hose clamp

• 3x total Cana Provisions tubing labels (1x clean, 1x dirty, 1x untreated)

MSR IWPS Kit Includes the following in addition to what is listed above:

• 1x MSR USMC IWPS (Microfilter AND ACTIVATED CARBON ELEMENT)

• 1x set of male/female QD fittings

• 1× 24” total section of US Made Silicone tubing

• 1x hose clamp

• 3x total Cana Provisions tubing labels (1x clean, 1x dirty, 1x untreated)

DISCLAIMER/WARNING - DO NOT DRINK WATER FROM A SETTLING BUCKET. THE SETTLING PROCESS DOES NOT QUALIFY AS AN ADEQUATE METHOD OF WATER TREATMENT AND/OR DISINFECTION. THE BLEACH AND IODINE DOSAGES PROVIDED ON THE WATER DATA CARD FAMILY OF PRODUCTS ARE IN ACCORDANCE AND ALIGNMENT WITH THE DOSAGES AS RECOMMENDED BY THE CDC AND EPA FOR SAFE WATER PREPARTION. PLEASE NOTE THAT THESE CONCENTRATIONS AND DOSES ARE CONSIDERABLY HIGHER THAN OTHER MANUFACTURED OPTIONS (AQUATABS, AQUAMIRA, H2GO) AND SHOULD BE TREATED ACCORDINGLY. CANA PROVISONS DOES NOT RECOMMEND THE USE OF HOUSEHOLD BLEACH AS YOUR PRIMARY WATER TREATMENT METHOD DUE TO THE VARYING CONCENTRATIONS OF BLEACH AND ITS DEGREDATION/DECOMPOSITION OVER TIME. FOLLOW ALL MANUFACTURER’S DIRECTIONS AND PERSONAL PROTECTIVE EQUIPMENT (PPE) FOR THE SAFE HANDLING OF BLEACH. DO NOT DRINK BLEACH. YOUR WATER TREATMENT IS YOUR RESPONSIBILITY.